How to Operation Fire Fighting Truck ?
Publish:CHENGLI SPECIAL AUTOMOBILE CO., LTD  Time:2020-10-29  Views:240

How to Operation Fire Fighting Truck ?

The correct use of Fire Truck , reasonable operation, win time, reduce failures, and successfully complete the fire fighting task. Users should be proficient in the use of this car.

Section 1 Fill the water tank with water

 To inject water into the water tank, you can use pressurized water such as the vehicle‘s water pump or city fire hydrant to directly inject it from the water injection port or maintenance hole through the hose (equipped with the vehicle). The operation method is as follows:

  •  1. Take out the hose from the equipment box, connect the fire hydrant wrench on the ground (or underground), connect one end of the hose to the water injection port (or put it directly into the tank from the maintenance hole), and connect the other end to the fire hydrant (or other pressure water source) ), open the fire hydrant with a wrench, and then pour water into the water tank.
  •  2. If the water pump of this vehicle is used to extract water from natural water sources, one end of the suction pipe can be connected to the water inlet pipe, and the other end to the water filter, put in the water, and close the water outlet valve. Run the water pump, wait for the water to be sucked up, then open the water injection valve, and the water can be injected into the tank.

 Section 2 How to use power take-off

 The power take-off is clamped between the clutch and the transmission. Pull the handle of the hand brake backwards before starting the water pump to fix the vehicle brake in place. Then start the engine, disconnect the clutch, push up the power take-off handle, and the power is transmitted to the water pump to run through the drive shaft.

 Section 3 for the use of water delivery system

 一) Water supply from water tank or fire hydrant

  •  1. Take out the water hose, water wheel, fire hydrant wrench and other equipment as needed, connect one end of the hose to the fire hydrant, and the other end to the water injection port, open the fire hydrant, and water is poured into the tank.
  •  2. After opening the water inlet valve, the water in the tank flows into the pump.
  •  3. Start the engine and engage the power take-off to make the water pump run.
  •  4. Open the water outlet valve or water cannon valve on both sides, and slowly increase the throttle to make the water pump pressurized for use.

二)Take power from natural water sources such as rivers, lakes and ponds

  •  1. Take out the water suction hose water filter, after installation, connect it to any water inlet on both sides of the car, and sink the water filter into the water source with a depth greater than 300mm to prevent air inhalation and affect the pumping effect, and do not touch the bottom. So as not to block the water filter with dirt. Check whether the sealing ring of each connection part is intact and whether the buckle is tightened to prevent air leakage.
  •  2. Take out the water hose, water gun and other equipment as needed, and connect them to the water inlets on both sides of the car.
  •  3. After opening the water inlet valve, the water in the tank flows into the pump.
  •  4. Start the engine, release the clutch, and engage the power take-off, so that the water pump is slowly pressurized.
  •  5. Open the water outlet valve or the water cannon valve and gradually increase the throttle to make the water pump enter the normal working state.


product list
Vacuum Suction Truck
Fuel Tank Truck / Trailer
Bitumen Spray Truck
Fire Fighting Truck
LED Advertisement Truck
Road Sweeper/Cleaning Truck
Refrigerator Truck
Water Tank Truck
Garbage truck
Truck Mounted Crane
Flatbed Truck
contact us
Tel : 86 0722 3288 526
Mob:008618995979503
E-mail:clwgroup@cn-vehicles.com
Address:South Suburb ChengLi Automobile Industry Park, SuiZhou City, HuBei Province, China.
wangqiufang
  • facebook

Copyright © 2019 CHENGLI SPECIAL AUTOMOBILE CO., LTD All Rights Reserved.

service